Andy from Sandy
Super member
Has the hw100x 250 bar regulator failed yet?
-
the Daily hi thread
RAW TM1000
- Thread starter Dh1r5ty
- Start date
I fill mine to 207 bar, when it has cooled it settles just above 200 bar.
I easily get 140 -150 shots before I get down to 100 bar.
My gun is shooting a very consistent 11.2 ft/lb with JSB Shorts.
Where’s that from mate, do you have a link?
rickrolfe1
Super member
Finally have one inbound...
Perfect looks nice too
Andy from Sandy
Super member
Is the CR2 worth the extra?
Only if you like the stock
NewtonN
Member
I only shoot outdoor.
Shorts work perfectly well outside, if it’s really windy I use JSB heavies.
Captain_Black
Proactive member
TM1000
A question
I shoot Benchrest with a HFT500
It's very accurate, but I would like to have another highly accurate rifle
I have pretty much narrowed it down to a TM1000 or a Red Wolf
I just wonder, as I don't hear too many complaints about the Red Wolf.
Have any of you done a direct comparison with a Red Wolf
I'm a bit undecided atm & it's a lot of money to spend if I get my decision wrong
A question
I shoot Benchrest with a HFT500
It's very accurate, but I would like to have another highly accurate rifle
I have pretty much narrowed it down to a TM1000 or a Red Wolf
I just wonder, as I don't hear too many complaints about the Red Wolf.
Have any of you done a direct comparison with a Red Wolf
I'm a bit undecided atm & it's a lot of money to spend if I get my decision wrong
Manchester
Super member
I have both the redwolf and tm1000 and both do well for benchrest the tm , you have more adjustable power on the tm so can tune it to pellet. Redwolf just shoots well
I have a Redwolf running alongside my TM1000.
Both are very accurate.
The TM fits me better than my Redwolf, so I find it easier to get a repeatable position and thus a little more accurate.
I’ve had the Redwolf a long time now and it’s been fantastically reliable.
NewtonN
Member
Trust me you will not be disappointedI have always liked the look of these, tempted
tjc_dev
Keen member
That PRS stock is beautiful - a good match!
MikeyB
Member Extraordinaire
Well, I’ve got to say this is the most pellet fussy gun I’ve ever owned. Tbh, I was almost ready to throw in the towel and ask for a refund when I discovered it likes H&N Barracuda 8’s. Still not convinced it’s as good as my Blackwolf but, I’ll persevere for a while now I know what food it likes. Next job will be to buy some more B 8’s and weigh them. MY PB is 248 on the forum’s bench rest comp using my BW and weighed JSB Heavies. I managed the same score with the TM1000 using B 8’s straight out of the tin so, really hoping I’ll do better with it. The trigger is absolutely sublime, best I’ve ever used and, I love the stock which fits me like a glove.
There’s a few pics attached. I’ve subsequently removed the 170mm EagleVision dovetail to picatinney adapter and swapped it for their 2 piece version as the single piece obstructed the breech a little.
The silencer is an AirMaks short model. I tried several using the supplied adapter (my gun’s got the threaded barrel) and couldn’t notice any difference in accuracy between them nor, indeed, when using the air stripper. The stripper is too loud for me (plus my regular club requires silencers to be fitted). I chose this one as it has plenty of meat in the back plate which has allowed me (read local engineer) to drill out the 1/2” UNF and retap an M16x1 thread - fits beautifully. And, it doesn’t need to be removed to fit into the case.
There’s a few pics attached. I’ve subsequently removed the 170mm EagleVision dovetail to picatinney adapter and swapped it for their 2 piece version as the single piece obstructed the breech a little.
The silencer is an AirMaks short model. I tried several using the supplied adapter (my gun’s got the threaded barrel) and couldn’t notice any difference in accuracy between them nor, indeed, when using the air stripper. The stripper is too loud for me (plus my regular club requires silencers to be fitted). I chose this one as it has plenty of meat in the back plate which has allowed me (read local engineer) to drill out the 1/2” UNF and retap an M16x1 thread - fits beautifully. And, it doesn’t need to be removed to fit into the case.
